SENECT FILTER|CONTROL - IoT Aquaculture Control System, App-controlled terminal for the automation of modern aquaculture. Controls water values by switching sensors and actuators.

SENECT FILTER|CONTROL 300W without alarm output Switzerland (Type J)

SENECT FILTER|CONTROL 300W without alarm output Switzerland (Type J)

SKU: 1210-CH
Category: Control Units

Technical Specification
Dimensions:	265 x 254 x 127 mm
Power supply:	85 - 265 V AC, 47 - 63 Hz
Sensor input ports:	3 x Senect Sensors
Output ports:	1 x High-Power output 2 x Actuator outputs 3 x 230 V AC
Signals of the actuator outputs:	24 V DC PWM, 0 - 10 V, 4 - 20 mA
Ingress protection:	IP54
Data transmission:	802.11 b/g/n 2.4 GHz WLAN, remote access via dynamic DNS, port forwarding and IPv4
Shipping weight:	3.8 kg

Power Supply: 150W

300W
Alarm Output: Without alarm output

With alarm output (potential-free conctact)
Mains Connector: EU / Schuko (Type F)

Switzerland (Type J)

2.099,00 €

incl. 19% VAT , plus

Delivery time: 0 - 7 Workdays (DE - int. shipments may differ)

Drum or belt filter control

Suitable for every drum or belt filter
Reliable hydrostatic pressure sensor technology
Eco- and Dynamic-Mode: water- and energy-saving
Wi-Fi: online alarm and monitoring

Example configuration - Drum- or belt filter control & monitoring

Sensor port 1: Water level sensor filter e.g. Water level probe PS
Sensor port 2: Water level sensor pond e.g. Water level probe PS
Sensor port 3: Temperature sensor TMP
Actuator port 1: Feeder or Alarm lamp VIS-LED or control of the filter motor via frequency converter
Actuator port 2: Solenoid valve for water M12 for automatic water refilling

High-Power output: 24 V DC filter motor
Mains outlet 1: Spray pump filter
Mains outlet 2: UV-C or 230 V AC filter motor
Mains outlet 3: Circulation pump
Data evaluation and settings via Wi-Fi and App
Notifications via push message and e-mail

The level sensor at sensor port 1 measures the water level in the filter and starts a backwash of the filter at the specified flush level. All cleaning parameters can be set by the user (e.g. flush level, backwash duration, post-cleaning time).

The UV-C lamp at mains outlet 2 and the circulation pump at mains outlet 3 will be switched off in case of an emergency (e.g. dry-running protection) and automatically switched on again when the system is alright.

App Screenshot: Recording of the water level in the pre-chamber of a pumped filter. The level rises until a cleaning is triggered. The level then drops rapidly due to backwashing of the filter.

The level probe at sensor slot 2 measures the water level in the pond and opens the solenoid valve at output 2 to refill missing water.

Various functions are available (e.g. additional temporal addition, frost protection, max. duration, leakage detection).

App Screenshot: Recording of the water level in the pond. The level drops slowly until the solenoid valve is opened and the missing water is refilled.

For example, an automatic feeder or a warning lamp can be connected to actuator slot 1.

Either another level sensor (differential operation), a temperature sensor TMP or a cover switch can be connected to sensor slot 3.

App Screenshot: Temperature recording over the last 30 days.

Advantages of SENECT's intelligent filter control systems

Low maintenance & resource-saving

the intensive cleaning programme²
the Eco Mode (saves up to 40% water)¹
the automatic water refill (with optionally available solenoid valve)¹

Safety

monitoring of water level and motor current (for 24 V DC motors)^1,2
alarm messages in case of error on smartphone, tablet or PC
alarm also possible with warning lamp or as signal to PLC
remote access: view past actions, measured values and current status online

User-friendly

easy installation thanks to plug connectors
subsequent installation on almost every filter possible
operation directly on the device, or conveniently via tablet or PC

The SENECT System

A modular, decentralized control system:
- ⇒ Simple expansion of existing systems
- ⇒ Increased safety through small, distributed units
- ⇒ Cost-effective installation due to low cabling effort
Wireless data connection via Wi-Fi:
- ⇒ Updates via Wi-Fi: Install new features free of charge
- ⇒ Cost-effective installation: No network cables required

The SENECT Control App

The SENECT Control App is a software for smartphones, tablets and computers (PC and Mac) to operate the SENECT control units.

Clear: Operation of all control units in one single software
Convenient: Perform actions (e.g. feeding), adjust settings
Informative: Graphical display of sensor measurements
Important: Receive alarm messages

The SENECT Control App allows you to integrate your SENECT control units into your WLAN network and use your smartphone, tablet or PC to make settings, trigger actions, receive alarm messages, view sensor readings live or save the recorded data locally (PC version only).

For example, with the SENECT Control App you can be notified by push message and email in case of an alarm, e.g. when the oxygen concentration falls below a specified level or when the filter stops (emergency stop).

With the SENECT Control App, you receive sensor values and the status of the respective devices (e.g. filter: last cleaning or solenoid valve: on / off) and thus maintain an overview of your system.

Benefit from the advantages of the SENECT Control App:

Easy and convenient setting of the settings
Always keep an eye on the water parameters even when on the move
Alarm when measured values exceed or fall below thresholds

The SENECT Control App requires access to the GPS of your mobile device (Android) to detect available WLAN networks. No personal data is collected or stored.

Further information on this can be found in our privacy policy.

Overview SENECT Controller

* 2 x Water level sensors, 1 x Cover switch

¹ Functions that are controlled by measuring the water level are only available when an optionally available SENECT level sensor PS or the level sensor EPS is connected. These functions are: Cleaning trigger after water level, emergency shutdown, Eco Mode, Dynamic Mode.

² Functions that require a controlled change of the motor speed are only available if the filter motor is connected via the 24 V DC output (OUT 3) or via the control of a frequency converter (for 230 V or 400 V filter motors). These functions include: Intensive cleaning, soft start, manual speed change.

Item information	Value
Item weight:	2,70 kg